PLEASE HELP PENN FOSTER QUESTION PLEASE!!!!! EXAMINATION 93041 Electric Heating Appliances and Fans?
1. In selecting the wire size for a line cord, you should remember that
A. No. 16 is larger than No. 12. C. No. 8 is smaller than No. 10.
B. No. 14 carries more current than No. 18. D. No. 4 carries less current than No. 6.
2. Which one of the following appliance parts gets the hardest service?
A. Switch C. Heating element
B. Thermostat D. Line cord
3. The color used for the hot side of house wiring is
A. green. C. gray.
B. white. D. black.
4. An AWG No. 16 line cord with type HPN insulation has an ampacity of
A. 12 amp. C. 15 amp.
B. 13 amp. D. 17 amp.
5. To heat a room quickly, some electric room heaters are provided with
A. a heavy metal case. C. a push-button switch.
B. a motor-driven fan. D. an automatic thermostat.
6. If the current flowing through an electric heater increases from 6 to 12 amp while the voltage remains
the same, the heat produced by the heater will be
A. reduced one-half. C. two times the original heat.
B. unchanged. D. four times the original heat.
7. The wires used in a heating element are usually made of
A. copper. C. aluminum.
B. steel. D. Nichrome.
8. Why does a thermostat blade bend when heated or cooled?
A. It is made of two different materials.
B. There is a difference in temperature between the blade ends.
C. Different currents are applied to each end.
D. Mechanical pressure is caused by the high resistance.
9. When you are checking an electric heating appliance, the first test made should be for
A. excessive leakage. C. an open circuit.
B. the normal voltage supply. D. low resistance.
10. Why should you NOT repair heating elements by soldering?
A. Solder does not conduct electric current.
B. Solder joints are mechanically too weak.
C. Solder melts at the operating temperature of the heater.
D. Soldered joints have too high a resistance.
11. What type of selector switch can be used to control the heat output of three elements connected in
parallel?
A. SPST switch C. DPDT switch
B. DPST switch D. Shorting-bar-type switch
12. Thermostats used in electric irons differ from those in small room heaters in that they are
A. smaller in size. C. connected directly to the appliance plug.
B. operative at higher temperatures. D. mechanically more fragile.
13. How can you clean out the scales in an electric iron without taking the iron apart?
A. By blowing out the holes with compressed air
B. By scraping the tank and tubes with a drill bit
C. By brushing the clogged tubes with a stiff wire brush
D. By rinsing the tank and holes with a water-diluted chemical
14. Bus bars are used in an electric iron as
A. thermostat supports.
B. heat-adjusting resistors.
C. connectors between the thermostat and the element.
D. electrical terminals.
15. The water in a spray iron is prevented from returning to the tank by the action of a
A. suction tube. C. water pump.
B. check valve. D. pressure spring.
16. The heating element in an electric iron is in good working order if the resistance across the terminals
of the element reads approximately
A. 0 ohms. C. 120 ohms.
B. 15 ohms. D. 1000 ohms.
17. Why does the heat of the heating element stop when the desired temperature in an electric iron is
reached?
A. The thermostat blade opens electrical contacts.
B. The circuit through the element is closed.
C. The switch bypasses the thermostat.
D. The contacts on the blade touch.
18. Jumpering out the resistors in a resistance-controlled three-speed fan will cause the motor to
A. run at highest speed. C. run at lowest speed.
B. run at medium speed. D. stop immediately.
19. A fan equipped with a gearbox is capable of
A. running at three speeds. C. oscillating from side to side.
B. being tilted downward. D. reversing the direction of the motor.
20. If the fan blades rattle while the fan is turning, you can stop the noise by
A. oiling the blades.
B. adjusting the blade angles and the blade tip position.
C. tightening the motor end bells and motor mounts.
D. cleaning the blade surfaces.
21. The recommended way to hold a loose hub on a fan is by
A. riveting. C. welding.
B. soldering. D. cementing.
22. Quiet operation of a fan depends mostly upon the
A. weight of the blades. C. motor balance.
B. material of the blades. D. balance of the blades.
23. The blades of small fans are made of
A. aluminum. C. tin.
B. steel. D. copper.
24. A modern variable-speed fan does NOT use
A. a tapped inductor. C. an electronic speed control.
B. a multiple-winding motor. D. a dropping resistor.
25. An attic fan, or power ventilator, may have its power inadvertently tapped from
A. an upstairs bathroom. C. a basement service.
B. an attic lighting circuit. D. an air conditioning circuit